ISO/TS 10303-1690:2018-11 Interconnect placement requirements


Application module: Interconnect placement requirements	ISO/TS 10303-1690:2018-11(E) © ISO

Cover page
Table of contents
Copyright
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
3.2 Abbreviated terms

4 Information requirements
4.1 Required AM ARM
4.2 ARM type definitions
4.3 ARM entity definitions
4.4 ARM subtype constraint definitions
4.5 ARM function definitions
5 Module interpreted model
5.1 Mapping specification
5.2 MIM EXPRESS short listing
5.2.1 MIM type definitions
5.2.2 MIM entity definitions
5.2.3 MIM subtype constraint definitions

A MIM short names
B Information object registration
C ARM EXPRESS-G
D MIM EXPRESS-G
E Computer interpretable listings
F Change history
Bibliography
Index

5.1 Mapping specification

In the following, "Application element" designates any entity data type defined in Clause 4, any of its explicit attributes and any subtype constraint. "MIM element" designates any entity data type defined in Clause 5.2 or imported with a USE FROM statement, from another EXPRESS schema, any of its attributes and any subtype constraint defined in Clause 5.2 or imported with a USE FROM statement.

This clause contains the mapping specification that defines how each application element of this part of ISO 10303 (see Clause 4) maps to one or more MIM elements (see Clause 5.2).

The mapping for each application element is specified in a separate subclause below. The mapping specification of an attribute of an ARM entity is a subclause of the clause that contains the mapping specification of this entity. Each mapping specification subclause contains up to five elements.

Title: The clause title contains:

the name of the considered ARM entity or subtype constraint, or
the name of the considered ARM entity atribute when this attribute refers to a type that is not an entity data type or a SELECT type that contains or may contain entity data types, or
a composite expression, <attribute name> to <referred type>, when this attribute refers to a type that is not an entity data type or a SELECT type that contains or may contain entity data types.

MIM element: This section contains, depending on the considered application element:

the name of one or more MIM entity data types;
the name of a MIM entity attribute, presented with the syntax <entity name>.<attribute name>, when the considered ARM attribute refers to a type that is not an entity data type or a SELECT type that contains or may contain entity data types;
the term PATH, when the considered ARM entity attribute refers to an entity data type or to a SELECT type that contains or may contain entity data types;
the term IDENTICAL MAPPING, when both application objects involved in an application assertion map to the same instance of a MIM entity data type;
the term NO MAPPING EXTENSION PROVIDED, when the extension to an extensible SELECT TYPE has no impact;
the syntax /SUPERTYPE(<supertype name>)/, when the considered ARM entity is mapped as its supertype;
one or more constructs /SUBTYPE(<subtype name>)/, when the mapping of the considered ARM entity is the union of the mapping of its subtypes.

When the mapping of an application element involves more than one MIM element, each of these MIM elements is presented on a separate line in the mapping specification, enclosed between parentheses or brackets.

Source: This section contains:

the ISO standard number and part number in which the MIM element is defined, for those MIM elements that are defined in a common resource document;
the ISO standard number and part number of this part of ISO 10303, for those MIM elements that are defined in the MIM schema of this part.

This section is omitted when the keywords PATH or IDENTICAL MAPPING or NO MAPPING EXTENSION PROVIDED are used in the MIM element section.

Rules: This section contains the name of one or more global rules that apply to the population of the MIM entity data types listed in the MIM element section or in the reference path. When no rule applies, this section is omitted.

A reference to a global rule may be followed by a reference to the subclause in which the rule is defined.

Constraint: This section contains the name of one or more subtype constraints that apply to the population of the MIM entity data types listed in the MIM element section or in the reference path. When no subtype constraint applies, this section is omitted.

A reference to a subtype constraint may be followed by a reference to the subclause in which the subtype constraint is defined.

Reference path: This section contains:

the reference path to its supertypes in the common resources, for each MIM element created within this part of ISO 10303;
the specification of the relationships between MIM elements, when the mapping of an application element requires to relate instances of several MIM entity data types. In such a case, each line in the reference path documents the role of a MIM element relative to the referring MIM element or to the next referred MIM element.

For the expression of reference paths and of the constraints between MIM elements, the following notational conventions apply:

[]	enclosed section constrains multiple MIM elements or sections of the reference path are required to satisfy an information requirement;
()	enclosed section constrains multiple MIM elements or sections of the reference path are identified as alternatives within the mapping to satisfy an information requirement;
{}	enclosed section constrains the reference path to satisfy an information requirement;
<>	enclosed section constrains at one or more required reference path;
\|\|	enclosed section constrains the supertype entity;
->	the attribute, whose name precedes the -> symbol, references the entity or select type whose name follows the -> symbol;
<-	the entity or select type, whose name precedes the <- symbol, is referenced by the entity attribute whose name follows the <- symbol;
[i]	the attribute, whose name precedes the [i] symbol, is an aggregate; any element of that aggregate is referred to;
[n]	the attribute, whose name precedes the [n] symbol, is an ordered aggregate; member n of that aggregate is referred to;
=>	the entity, whose name precedes the => symbol, is a supertype of the entity whose name follows the => symbol;
<=	the entity, whose name precedes the <= symbol, is a subtype of the entity whose name follows the <= symbol;
=	the string, select, or enumeration type is constrained to a choice or value;
\	the reference path expression continues on the next line;
*	one or more instances of the relationship entity data type may be assembled in a relationship tree structure. The path between the relationship entity and the related entities, is enclosed with braces;
--	the text following is a comment or introduces a clause reference;
*>	the select or enumeration type, whose name precedes the > symbol, is extended into the select or enumeration type whose name follows the > symbol;
<*	the select or enumeration type, whose name precedes the <* symbol, is an extension of the select or enumeration type whose name follows the <* symbol;
!{}	section enclosed by {} indicates a negative constraint placed on the mapping.

The definition and use of mapping templates is not supported in the present version of the application modules. However, use of predefined templates /SUBTYPE/ and /SUPERTYPE/ is supported.

5.1.1 Area_qualified_layout_spacing_requirement

MIM element:	area_qualified_layout_spacing_requirement
Source:	ISO 10303-1690
Reference path:	area_qualified_layout_spacing_requirement <= layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition

5.1.1.1 Area_qualified_layout_spacing_requirement to Layout_spacing_contextual_area (as area_context)

MIM element:

PATH

Reference path:

area_qualified_layout_spacing_requirement <=
layout_spacing_requirement <=
predefined_requirement_view_definition <=
product_definition
characterized_product_definition = product_definition
characterized_product_definition
characterized_definition = characterized_product_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.related_property_definition
{property_definition_relationship
property_definition_relationship.name = 'area context'}
property_definition_relationship.relating_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect =>
layout_spacing_contextual_area

5.1.2 Interconnect_module_constraint_region

MIM element:	group_shape_aspect
Source:	ISO 10303-1706
Reference path:	group_shape_aspect <= shape_aspect {shape_aspect shape_aspect.description = 'interconnect module constraint region'}

5.1.2.1 design_specific_purpose

MIM element:	descriptive_representation_item
Source:	ISO 10303-45
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect shape_definition characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_representation.definition property_definition_representation property_definition_representation.used_representation -> representation representation.items[i] -> {representation_item representation_item.name = 'design specific purpose'} representation_item => descriptive_representation_item descriptive_representation_item.description

5.1.2.2 keepout

MIM element:	descriptive_representation_item
Source:	ISO 10303-45
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect shape_definition characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_representation.definition property_definition_representation property_definition_representation.used_representation -> representation representation.items[i] -> {representation_item representation_item.name = 'keepout'} representation_item => descriptive_representation_item {descriptive_representation_item (descriptive_representation_item.description = 'true') (descriptive_representation_item.description = 'false')}

5.1.2.3 Interconnect_module_constraint_region to Component_termination_passage (as non_conformant_interconnect_module_design_object)

MIM element:

PATH

Reference path:

group_shape_aspect <=
shape_aspect <-
shape_aspect_relationship.related_shape_aspect
shape_aspect_relationship
{shape_aspect_relationship
shape_aspect_relationship.name = 'constraint region violation'}
shape_aspect_relationship.relating_shape_aspect ->
shape_aspect
shape_aspect.of_shape ->
product_definition_shape =>
assembly_component =>
laminate_component =>
inter_stratum_feature =>
plated_inter_stratum_feature =>
plated_passage =>
component_termination_passage

5.1.2.4 Interconnect_module_constraint_region to Conductive_filled_area (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.2.5 Interconnect_module_constraint_region to Conductor (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.2.6 Interconnect_module_constraint_region to Cutout (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature => cutout

5.1.2.7 Interconnect_module_constraint_region to Group (as constrained_design_object_category)

MIM element:	group
Source:	ISO 10303-1690
Reference path:	group_shape_aspect groupable_item = group_shape_aspect groupable_item <- applied_group_assignment.items[i] applied_group_assignment <= group_assignment {group_assignment.role -> object_role object_role.name = 'constrained object'} group_assignment.assigned_group -> group

5.1.2.8 Interconnect_module_constraint_region to Inter_stratum_extent (as associated_stratum_extent)

MIM element:

PATH

Reference path:

group_shape_aspect <=
shape_aspect
shape_definition = shape_aspect
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.related_property_definition
{property_definition_relationship
property_definition_relationship.name = 'associated stratum extent'}
property_definition_relationship.relating_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = characterized_product_definition
characterized_product_definition
characterized_product_definition = product_definition_relationship
product_definition_relationship
{product_definition_relationship
product_definition_relationship.name = 'inter stratum extent'}

5.1.2.9 Interconnect_module_constraint_region to Inter_stratum_feature (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature

5.1.2.10 Interconnect_module_constraint_region to interconnect_module_design_object_category (as constrained_design_object_category)

MIM element:	interconnect_module_design_object_category
Source:	ISO 10303-1690
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition property_definition_relationship {property_definition_relationship property_definition_relationship.name = 'constrained object'} property_definition_relationship.related_property_definition -> property_definition property_definition.definition -> characterized_definition characterized_definition = characterized_object characterized_object {characterized_object [(characterized_object.description = 'assembly component category') (characterized_object.description = 'cutout category') (characterized_object.description = 'embedded physical component terminal category') (characterized_object.description = 'fill area category') (characterized_object.description = 'inter stratum feature category') (characterized_object.description = 'stratum feature category') (characterized_object.description = 'via category')] [characterized_object => interconnect_module_design_object_category]}

5.1.2.11 Interconnect_module_constraint_region to interconnect_module_design_object_select (as non_conformant_interconnect_module_design_object)

MIM element:

PATH

Reference path:

group_shape_aspect <=
shape_aspect <-
shape_aspect_relationship.related_shape_aspect
shape_aspect_relationship
{shape_aspect_relationship
shape_aspect_relationship.name = 'constraint region violation'}
shape_aspect_relationship.relating_shape_aspect ->
shape_aspect
(shape_aspect =>
stratum_feature)
(shape_aspect.of_shape ->
product_definition_shape
(product_definition_shape =>
assembly_component)
(product_definition_shape =>
stratum))

5.1.2.12 Interconnect_module_constraint_region to Laminate_component (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component

5.1.2.13 Interconnect_module_constraint_region to Land (as non_conformant_interconnect_module_design_object)

MIM element:

PATH

Reference path:

5.1.2.14 Interconnect_module_constraint_region to Layered_interconnect_module_design_view (as associated_definition)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect shape_aspect.of_shape -> product_definition_shape => physical_unit => interconnect_module_design_view => layered_interconnect_module_design_view

5.1.2.15 Interconnect_module_constraint_region to Printed_component (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => printed_component

5.1.2.16 Interconnect_module_constraint_region to Stratum (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect.of_shape -> product_definition_shape => stratum

5.1.2.17 Interconnect_module_constraint_region to Stratum_feature (as non_conformant_interconnect_module_design_object)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'constraint region violation'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.2.18 Interconnect_module_constraint_region to Via (as non_conformant_interconnect_module_design_object)

MIM element:

PATH

Reference path:

5.1.3 Layer_qualified_layout_spacing_requirement

MIM element:	layer_qualified_layout_spacing_requirement
Source:	ISO 10303-1670
Reference path:	layer_qualified_layout_spacing_requirement <= layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition

5.1.3.1 Layer_qualified_layout_spacing_requirement to Inter_stratum_extent (as layer_context)

MIM element:

PATH

Reference path:

layer_qualified_layout_spacing_requirement <=
layout_spacing_requirement <=
predefined_requirement_view_definition <=
product_definition
characterized_product_definition = product_definition
characterized_product_definition
characterized_definition = characterized_product_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.related_property_definition
{property_definition_relationship
property_definition_relationship.name = 'layer context'}
property_definition_relationship.relating_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = characterized_product_definition
characterized_product_definition
characterized_product_definition = product_definition_relationship
{product_definition_relationship
product_definition_relationship.name = 'inter stratum extent'}
product_definition_relationship

5.1.4 Layout_spacing_contextual_area

MIM element:	layout_spacing_contextual_area
Source:	ISO 10303-1690
Reference path:	layout_spacing_contextual_area <= shape_aspect

5.1.4.1 Layout_spacing_contextual_area to Assembly_module_design_view (as associated_definition)

MIM element:	PATH
Reference path:	layout_spacing_contextual_area <= shape_aspect shape_aspect.of_shape -> product_definition_shape => physical_unit => assembly_module_design_view

5.1.4.2 Layout_spacing_contextual_area to Interconnect_module_component_surface_feature (as reference_surface)

MIM element:

PATH

Reference path:

layout_spacing_contextual_area <=
shape_aspect <-
shape_aspect_relationship.relating_shape_aspect
{shape_aspect_relationship
shape_aspect_relationship.name = 'reference surface'}
shape_aspect_relationship
shape_aspect_relationship.related_shape_aspect ->
{shape_aspect.description = 'interconnect module component surface feature'}
shape_aspect =>
component_feature =>
physical_component_feature =>
interconnect_module_component_surface_feature

5.1.5 Layout_spacing_requirement

MIM element:	layout_spacing_requirement
Source:	ISO 10303-1690
Reference path:	layout_spacing_requirement <= predefined_requirement_view_definition

5.1.5.1 design_object_category_1

MIM element:	characterized_object.name
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition characterized_product_definition = product_definition characterized_product_definition characterized_definition = characterized_product_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition {property_definition_relationship.name = 'design object category 1'} property_definition_relationship.related_property_definition -> property_definition property_definition.definition -> characterized_definition characterized_definition = characterized_object characterized_object characterized_object.name {(characterized_object.name = 'assembly component category') (characterized_object.name = 'assembly module category') (characterized_object.name = 'assembly module component category') (characterized_object.name = 'assembly module component terminal category') (characterized_object.name = 'assembly module macro component category') (characterized_object.name = 'assembly module macro component join terminal category') (characterized_object.name = 'bare die component category') (characterized_object.name = 'bare die component terminal category') (characterized_object.name = 'buried via category') (characterized_object.name = 'cable component category') (characterized_object.name = 'component feature category') (characterized_object.name = 'component mounting feature category') (characterized_object.name = 'component termination passage category') (characterized_object.name = 'component termination passage interface terminal category') (characterized_object.name = 'component termination passage join terminal category') (characterized_object.name = 'conductive interconnect element terminal category') (characterized_object.name = 'conductive interconnect element with pre defined transitions category') (characterized_object.name = 'conductive interconnect element with user defined single transition category') (characterized_object.name = 'connected area component category') (characterized_object.name = 'contact size dependent land category') (characterized_object.name = 'cutout category') (characterized_object.name = 'cutout edge segment category') (characterized_object.name = 'dielectric material passage category') (characterized_object.name = 'electrical isolation laminate component category') (characterized_object.name = 'embedded physical component terminal category') (characterized_object.name = 'fiducial category') (characterized_object.name = 'fill area category') (characterized_object.name = 'inter stratum feature category') (characterized_object.name = 'interconnect component interface terminal category') (characterized_object.name = 'interconnect component join terminal category') (characterized_object.name = 'interconnect module component category') (characterized_object.name = 'interconnect module component stratum based terminal category') (characterized_object.name = 'interconnect module component surface feature category') (characterized_object.name = 'interconnect module component terminal category') (characterized_object.name = 'interconnect module edge category') (characterized_object.name = 'interconnect module edge segment category') (characterized_object.name = 'interconnect module macro component category') (characterized_object.name = 'interconnect module macro component join terminal category') (characterized_object.name = 'interface access material removal laminate component category') (characterized_object.name = 'interface access stratum feature template component category') (characterized_object.name = 'interface component category') (characterized_object.name = 'interfacial connection category') (characterized_object.name = 'internal probe access area category') (characterized_object.name = 'laminate component category') (characterized_object.name = 'generic laminate text component category') (characterized_object.name = 'laminate text string component category') (characterized_object.name = 'land category') (characterized_object.name = 'land interface terminal category') (characterized_object.name = 'land join terminal category') (characterized_object.name = 'material removal laminate component category') (characterized_object.name = 'minimally defined component terminal category') (characterized_object.name = 'movable packaged component join terminal category') (characterized_object.name = 'multi layer material removal laminate component category') (characterized_object.name = 'multi stratum special symbol component category') (characterized_object.name = 'non conductive base blind via category') (characterized_object.name = 'packaged component category') (characterized_object.name = 'packaged component join terminal category') (characterized_object.name = 'packaged connector component category') (characterized_object.name = 'packaged connector component interface terminal category') (characterized_object.name = 'partially plated cutout category') (characterized_object.name = 'partially plated interconnect module edge category') (characterized_object.name = 'physical component category') (characterized_object.name = 'physical connectivity interrupting cutout category') (characterized_object.name = 'physical laminate component category') (characterized_object.name = 'physical network supporting inter stratum feature category') (characterized_object.name = 'plated conductive base blind via category') (characterized_object.name = 'plated cutout category') (characterized_object.name = 'plated cutout edge segment category') (characterized_object.name = 'plated interconnect module edge category') (characterized_object.name = 'plated interconnect module edge segment category') (characterized_object.name = 'plated passage category') (characterized_object.name = 'plated passage or unsupported passage category') (characterized_object.name = 'primary stratum indicator symbol category') (characterized_object.name = 'printed component join terminal category') (characterized_object.name = 'printed connector component interface terminal category') (characterized_object.name = 'probe access area category') (characterized_object.name = 'routed interconnect component category') (characterized_object.name = 'routed physical component category') (characterized_object.name = 'special symbol laminate component category') (characterized_object.name = 'stratum feature category') (characterized_object.name = 'stratum feature template component category') (characterized_object.name = 'thermal isolation laminate component category') (characterized_object.name = 'unrouted conductive interconnect element category') (characterized_object.name = 'unsupported passage category') (characterized_object.name = 'via category') (characterized_object.name = 'via terminal category')}

5.1.5.2 design_object_category_2

MIM element:	characterized_object.name
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition characterized_product_definition = product_definition characterized_product_definition characterized_definition = characterized_product_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition {property_definition_relationship.name = 'design object category 2'} property_definition_relationship.related_property_definition -> property_definition property_definition.definition -> characterized_definition characterized_definition = characterized_object characterized_object characterized_object.name {(characterized_object.name = 'assembly component category') (characterized_object.name = 'assembly module category') (characterized_object.name = 'assembly module component category') (characterized_object.name = 'assembly module component terminal category') (characterized_object.name = 'assembly module macro component category') (characterized_object.name = 'assembly module macro component join terminal category') (characterized_object.name = 'bare die component category') (characterized_object.name = 'bare die component terminal category') (characterized_object.name = 'buried via category') (characterized_object.name = 'cable component category') (characterized_object.name = 'component feature category') (characterized_object.name = 'component mounting feature category') (characterized_object.name = 'component termination passage category') (characterized_object.name = 'component termination passage interface terminal category') (characterized_object.name = 'component termination passage join terminal category') (characterized_object.name = 'conductive interconnect element terminal category') (characterized_object.name = 'conductive interconnect element with pre defined transitions category') (characterized_object.name = 'conductive interconnect element with user defined single transition category') (characterized_object.name = 'connected area component category') (characterized_object.name = 'contact size dependent land category') (characterized_object.name = 'cutout category') (characterized_object.name = 'cutout edge segment category') (characterized_object.name = 'dielectric material passage category') (characterized_object.name = 'electrical isolation laminate component category') (characterized_object.name = 'embedded physical component terminal category') (characterized_object.name = 'fiducial category') (characterized_object.name = 'fill area category') (characterized_object.name = 'inter stratum feature category') (characterized_object.name = 'interconnect component interface terminal category') (characterized_object.name = 'interconnect component join terminal category') (characterized_object.name = 'interconnect module component category') (characterized_object.name = 'interconnect module component stratum based terminal category') (characterized_object.name = 'interconnect module component surface feature category') (characterized_object.name = 'interconnect module component terminal category') (characterized_object.name = 'interconnect module edge category') (characterized_object.name = 'interconnect module edge segment category') (characterized_object.name = 'interconnect module macro component category') (characterized_object.name = 'interconnect module macro component join terminal category') (characterized_object.name = 'interface access material removal laminate component category') (characterized_object.name = 'interface access stratum feature template component category') (characterized_object.name = 'interface component category') (characterized_object.name = 'interfacial connection category') (characterized_object.name = 'internal probe access area category') (characterized_object.name = 'laminate component category') (characterized_object.name = 'generic laminate text component category') (characterized_object.name = 'laminate text string component category') (characterized_object.name = 'land category') (characterized_object.name = 'land interface terminal category') (characterized_object.name = 'land join terminal category') (characterized_object.name = 'material removal laminate component category') (characterized_object.name = 'minimally defined component terminal category') (characterized_object.name = 'movable packaged component join terminal category') (characterized_object.name = 'multi layer material removal laminate component category') (characterized_object.name = 'multi stratum special symbol component category') (characterized_object.name = 'non conductive base blind via category') (characterized_object.name = 'packaged component category') (characterized_object.name = 'packaged component join terminal category') (characterized_object.name = 'packaged connector component category') (characterized_object.name = 'packaged connector component interface terminal category') (characterized_object.name = 'partially plated cutout category') (characterized_object.name = 'partially plated interconnect module edge category') (characterized_object.name = 'physical component category') (characterized_object.name = 'physical connectivity interrupting cutout category') (characterized_object.name = 'physical laminate component category') (characterized_object.name = 'physical network supporting inter stratum feature category') (characterized_object.name = 'plated conductive base blind via category') (characterized_object.name = 'plated cutout category') (characterized_object.name = 'plated cutout edge segment category') (characterized_object.name = 'plated interconnect module edge category') (characterized_object.name = 'plated interconnect module edge segment category') (characterized_object.name = 'plated passage category') (characterized_object.name = 'plated passage or unsupported passage category') (characterized_object.name = 'primary stratum indicator symbol category') (characterized_object.name = 'printed component join terminal category') (characterized_object.name = 'printed connector component interface terminal category') (characterized_object.name = 'probe access area category') (characterized_object.name = 'routed interconnect component category') (characterized_object.name = 'routed physical component category') (characterized_object.name = 'single stratum special symbol component category') (characterized_object.name = 'stratum feature category') (characterized_object.name = 'stratum feature template component category') (characterized_object.name = 'thermal isolation laminate component category') (characterized_object.name = 'unrouted conductive interconnect element category') (characterized_object.name = 'unsupported passage category') (characterized_object.name = 'via category') (characterized_object.name = 'via terminal category')}

5.1.5.3 of_spacing_type

MIM element:

PATH

Reference path:

layout_spacing_requirement <=
predefined_requirement_view_definition <=
product_definition
characterized_product_definition = product_definition
characterized_product_definition
characterized_definition = characterized_product_definition
characterized_definition <-
property_definition.definition
property_definition
{property_definition.name = 'of spacing type'}
property_definition.description
{(property_definition.description = 'nearest boundary')
(property_definition.description = 'centroid')
(property_definition.description = 'furthest boundary')}

5.1.5.4 Layout_spacing_requirement to Group (as design_object_category_1)

MIM element:	group
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement groupable_item = layout_spacing_requirement groupable_item <- applied_group_assignment.items[i] applied_group_assignment <= group_assignment {group_assignment.role -> object_role object_role.name = 'design object category 1'} group_assignment.assigned_group -> group

5.1.5.5 Layout_spacing_requirement to Group (as design_object_category_2)

MIM element:	group
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement groupable_item = layout_spacing_requirement groupable_item <- applied_group_assignment.items[i] applied_group_assignment <= group_assignment {group_assignment.role -> object_role object_role.name = 'design object category 2'} group_assignment.assigned_group -> group

5.1.5.6 Layout_spacing_requirement to Length_tolerance_characteristic (as spacing)

MIM element:

PATH

Reference path:

layout_spacing_requirement <=
predefined_requirement_view_definition <=
product_definition
characterized_product_definition = product_definition
characterized_product_definition
characterized_definition = characterized_product_definition
characterized_definition <-
property_definition.definition
{property_definition.name = 'required characteristic'}
property_definition <-
property_definition_representation.definition
property_definition_representation
property_definition_representation.used_representation ->
representation

5.1.5.7 Layout_spacing_requirement to Stratum (as design_object_category_1)

MIM element:	characterized_object.name
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition characterized_product_definition = product_definition characterized_product_definition characterized_definition = characterized_product_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition {property_definition_relationship.name = 'design object category 1'} property_definition_relationship.related_property_definition -> property_definition => product_definition_shape => stratum

5.1.5.8 Layout_spacing_requirement to Stratum (as design_object_category_2)

MIM element:	characterized_object.name
Source:	ISO 10303-41
Reference path:	layout_spacing_requirement <= predefined_requirement_view_definition <= product_definition characterized_product_definition = product_definition characterized_product_definition characterized_definition = characterized_product_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition {property_definition_relationship.name = 'design object category 2'} property_definition_relationship.related_property_definition -> property_definition => product_definition_shape => stratum

5.1.6 Layout_spacing_requirement_non_conforming_design_object

MIM element:	shape_aspect_relationship
Source:	ISO 10303-41
Reference path:	{shape_aspect_relationship shape_aspect_relationship.name = 'layout spacing requirement violation'}

5.1.6.1 intersection_violation

MIM element:

PATH

Reference path:

5.1.6.2 Layout_spacing_requirement_non_conforming_design_object to Assembly_component (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component

5.1.6.3 Layout_spacing_requirement_non_conforming_design_object to Assembly_component (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component

5.1.6.4 Layout_spacing_requirement_non_conforming_design_object to Assembly_component (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.5 Layout_spacing_requirement_non_conforming_design_object to assembly_or_interconnect_design_object_select (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect (shape_aspect => stratum_feature) (shape_aspect => component_feature) (shape_aspect.of_shape -> product_definition_shape => assembly_component) (shape_aspect.of_shape -> product_definition_shape => stratum)

5.1.6.6 Layout_spacing_requirement_non_conforming_design_object to assembly_or_interconnect_design_object_select (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect (shape_aspect => stratum_feature) (shape_aspect => component_feature) (shape_aspect.of_shape -> product_definition_shape => assembly_component) (shape_aspect.of_shape -> product_definition_shape => stratum)

5.1.6.7 Layout_spacing_requirement_non_conforming_design_object to assembly_or_interconnect_design_object_select (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition
(property_definition =>
product_definition_shape =>
assembly_component)
(property_definition =>
product_definition_shape =>
stratum)
(property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect
(shape_aspect =>
stratum_feature)
(shape_aspect =>
component_feature))

5.1.6.8 Layout_spacing_requirement_non_conforming_design_object to Component_feature (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect => component_feature

5.1.6.9 Layout_spacing_requirement_non_conforming_design_object to Component_feature (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect => component_feature

5.1.6.10 Layout_spacing_requirement_non_conforming_design_object to Component_feature (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect =>
component_feature

5.1.6.11 Layout_spacing_requirement_non_conforming_design_object to Component_termination_passage (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature => plated_inter_stratum_feature => plated_passage => component_termination_passage

5.1.6.12 Layout_spacing_requirement_non_conforming_design_object to Component_termination_passage (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature => plated_inter_stratum_feature => plated_passage => component_termination_passage

5.1.6.13 Layout_spacing_requirement_non_conforming_design_object to Component_termination_passage (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition =>
product_definition_shape =>
assembly_component =>
laminate_component =>
inter_stratum_feature =>
plated_inter_stratum_feature =>
plated_passage

5.1.6.14 Layout_spacing_requirement_non_conforming_design_object to Conductive_filled_area (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.6.15 Layout_spacing_requirement_non_conforming_design_object to Conductive_filled_area (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect => stratum_feature

5.1.6.16 Layout_spacing_requirement_non_conforming_design_object to Conductive_filled_area (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect
shape_aspect =>
stratum_feature

5.1.6.17 Layout_spacing_requirement_non_conforming_design_object to Conductor (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.6.18 Layout_spacing_requirement_non_conforming_design_object to Conductor (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect => stratum_feature

5.1.6.19 Layout_spacing_requirement_non_conforming_design_object to Conductor (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect
shape_aspect =>
stratum_feature

5.1.6.20 Layout_spacing_requirement_non_conforming_design_object to Cutout (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature => cutout

5.1.6.21 Layout_spacing_requirement_non_conforming_design_object to Cutout (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature => cutout

5.1.6.22 Layout_spacing_requirement_non_conforming_design_object to Cutout (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.23 Layout_spacing_requirement_non_conforming_design_object to Geometric_model (as violation_shape)

MIM element:

PATH

Reference path:

5.1.6.24 Layout_spacing_requirement_non_conforming_design_object to Inter_stratum_feature (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature

5.1.6.25 Layout_spacing_requirement_non_conforming_design_object to Inter_stratum_feature (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => inter_stratum_feature

5.1.6.26 Layout_spacing_requirement_non_conforming_design_object to Inter_stratum_feature (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.27 Layout_spacing_requirement_non_conforming_design_object to Laminate_component (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component

5.1.6.28 Layout_spacing_requirement_non_conforming_design_object to Laminate_component (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component

5.1.6.29 Layout_spacing_requirement_non_conforming_design_object to Laminate_component (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.30 Layout_spacing_requirement_non_conforming_design_object to Land (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => stratum_feature_template_component => land

5.1.6.31 Layout_spacing_requirement_non_conforming_design_object to Land (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => laminate_component => stratum_feature_template_component => land

5.1.6.32 Layout_spacing_requirement_non_conforming_design_object to Land (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition =>
product_definition_shape =>
assembly_component =>
laminate_component =>
stratum_feature_template_component =>
land

5.1.6.33 Layout_spacing_requirement_non_conforming_design_object to Layout_spacing_requirement (as design_requirement)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'design requirement'}
property_definition_relationship.related_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = characterized_product_definition
characterized_product_definition
characterized_product_definition = product_definition
product_definition =>
predefined_requirement_view_definition =>
layout_spacing_requirement

5.1.6.34 Layout_spacing_requirement_non_conforming_design_object to Length_data_element (as violation_value)

MIM element:

PATH

Reference path:

5.1.6.35 Layout_spacing_requirement_non_conforming_design_object to Printed_component (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => printed_component

5.1.6.36 Layout_spacing_requirement_non_conforming_design_object to Printed_component (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => assembly_component => printed_component

5.1.6.37 Layout_spacing_requirement_non_conforming_design_object to Printed_component (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.38 Layout_spacing_requirement_non_conforming_design_object to Stratum (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => stratum

5.1.6.39 Layout_spacing_requirement_non_conforming_design_object to Stratum (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect shape_aspect.of_shape -> product_definition_shape => stratum

5.1.6.40 Layout_spacing_requirement_non_conforming_design_object to Stratum (as non_conformant_design_object)

MIM element:

PATH

Reference path:

5.1.6.41 Layout_spacing_requirement_non_conforming_design_object to Stratum_feature (as design_object_1)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.relating_shape_aspect -> shape_aspect => stratum_feature

5.1.6.42 Layout_spacing_requirement_non_conforming_design_object to Stratum_feature (as design_object_2)

MIM element:	PATH
Reference path:	shape_aspect_relationship shape_aspect_relationship.related_shape_aspect -> shape_aspect => stratum_feature

5.1.6.43 Layout_spacing_requirement_non_conforming_design_object to Stratum_feature (as non_conformant_design_object)

MIM element:

PATH

Reference path:

shape_aspect_relationship
shape_definition = shape_aspect_relationship
shape_definition
characterized_definition = shape_definition
characterized_definition <-
property_definition.definition
property_definition <-
property_definition_relationship.relating_property_definition
property_definition_relationship
{property_definition_relationship
property_definition_relationship.name = 'non conformant design object'}
property_definition_relationship.related_property_definition ->
property_definition
property_definition.definition ->
characterized_definition
characterized_definition = shape_definition
shape_definition
shape_definition = shape_aspect
shape_aspect
shape_aspect =>
stratum_feature

5.1.7 Requirement_assignment

This application object, Requirement_assignment, is defined in the module requirement_assignment. This mapping section extends the mapping of Requirement_assignment, to include assertions defined in this module.

5.1.7.1 Requirement_assignment to Interconnect_module_constraint_region (as assigned_to)

Reference path:

requirement_assignment <-
requirement_assigned_object.assigned_group
requirement_assigned_object
requirement_assigned_object.items ->
requirement_assigned_item
requirement_assigned_item *> ipr_requirement_assigned_item
ipr_requirement_assigned_item =
group_shape_aspect
{group_shape_aspect <=
shape_aspect
shape_aspect.description = 'interconnect module constraint region'}

5.1.7.2 Requirement_assignment to Stratum_constraint_region (as assigned_to)

Reference path:

5.1.8 Stratum_constraint_region

MIM element:	group_shape_aspect
Source:	ISO 10303-1706
Reference path:	group_shape_aspect <= shape_aspect {shape_aspect shape_aspect.description = 'stratum constraint region'}

5.1.8.1 design_specific_purpose

MIM element:	descriptive_representation_item.description
Source:	ISO 10303-45
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect shape_definition characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_representation.definition property_definition_representation property_definition_representation.used_representation -> representation representation.items[i] -> {representation_item representation_item.name = 'design specific purpose'} representation_item => descriptive_representation_item descriptive_representation_item.description

5.1.8.2 keepout

MIM element:	descriptive_representation_item
Source:	ISO 10303-45
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect shape_definition characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_representation.definition property_definition_representation property_definition_representation.used_representation -> representation representation.items[i] -> {representation_item representation_item.name = 'keepout'} representation_item => descriptive_representation_item {descriptive_representation_item (descriptive_representation_item.description = 'true') (descriptive_representation_item.description = 'false')}

5.1.8.3 Stratum_constraint_region to Layered_interconnect_module_design_view (as associated_definition)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect shape_aspect.of_shape -> product_definition_shape => physical_unit => interconnect_module_design_view => layered_interconnect_module_design_view

5.1.8.4 Stratum_constraint_region to Stratum (as constrained_stratum)

MIM element:	interconnect_module_design_object_category
Source:	ISO 10303-1690
Reference path:	group_shape_aspect <= shape_aspect shape_definition = shape_aspect characterized_definition = shape_definition characterized_definition <- property_definition.definition property_definition <- property_definition_relationship.relating_property_definition property_definition_relationship {property_definition_relationship property_definition_relationship.name = 'constrained stratum'} property_definition_relationship.related_property_definition -> property_definition => product_definition_shape => stratum

5.1.8.5 Stratum_constraint_region to Stratum (as non_conformant_stratum)

MIM element:	PATH
Reference path:	group_shape_aspect <= shape_aspect <- shape_aspect_relationship.related_shape_aspect shape_aspect_relationship {shape_aspect_relationship shape_aspect_relationship.name = 'non conformant stratum'} shape_aspect_relationship.relating_shape_aspect -> shape_aspect.of_shape -> product_definition_shape => stratum

5.1.9 ipr_non_feature_shape_element_subtypes

Some members of this constraint map to entity group_shape_aspect with additional constraints in the mapping. Population constraints on group_shape_aspect are to be provided by a higher level module.

Constraint:

ipr_non_feature_shape_element_subtypes

5.1.10 ipr_predefined_requirement_view_definition_subtypes

All members of this constraint maps to entity predefined_requirement_view_definition with additional constraints in the mapping. All of them require UNIQUE string for group.name, so ONEOF subtype constraint from ARM is guaranteed as not violated.

Constraint:	predefined_requirement_view_definition
Source:	ISO 10303-1670