|
|
Application module:
Sequential laminate assembly design |
ISO/TS 10303-1741:2018-11(E)
© ISO
|
This clause specifies the EXPRESS schema derived from the mapping
table.
It uses elements from the common resources or from other application
modules and defines the EXPRESS constructs that are specific to this
part of ISO 10303.
This clause constitutes the Module Interpreted Module (MIM) of the
application module.
This clause also
specifies the modifications that apply to the constructs
imported from the common resources.
The following restrictions apply to the use, in this schema, of constructs defined in common resources or in application
modules:
-
use of a supertype entity does not make applicable any of its
specializations, unless the specialization is also imported in the
MIM schema;
-
use of a SELECT type does not make applicable any of its listed types
unless the listed type is also imported in the MIM schema.
Short names of entities defined in this schema are described in Annex A. Unambiguous identification of this schema is defined
in Annex B.
EXPRESS specification:
*)
SCHEMA Sequential_laminate_assembly_design_mim;
USE FROM
Layered_interconnect_module_design_mim;
--
ISO/TS 10303-1698
(*
NOTE 1
The schemas referenced above are specified in the following
part of ISO 10303:
| Layered_interconnect_module_design_mim |
ISO/TS 10303-1698 |
NOTE 2
See Annex D,
Figures
D.1and D.2
for a graphical representation of this schema.
This subclause specifies the MIM types
for this application module. The MIM types and
definitions are specified below.
The slad_groupable_item type is an extension
of the
groupable_item type.
It adds the data
types
group_relationship, and assembly_component_usage
to the list of alternate data types.
EXPRESS specification:
*)
TYPE
slad_groupable_item =
SELECT
BASED_ON
groupable_item
WITH
(group_relationship,
assembly_component_usage);
END_TYPE;
(*
The slad_requirement_assigned_item type is an extension
of the
requirement_assigned_item type.
It adds the data
types
derived_laminate_assignment, and assembly_component_usage
to the list of alternate data types.
NOTE The list of entity data types may be
extended in application modules that use the constructs of
this module.
EXPRESS specification:
*)
TYPE
slad_requirement_assigned_item =
EXTENSIBLE
GENERIC_ENTITY
SELECT
BASED_ON
requirement_assigned_item
WITH
(derived_laminate_assignment,
assembly_component_usage);
END_TYPE;
(*
This subclause specifies the MIM entities for this
module. The MIM entities and definitions are specified below.
A derived_laminate_assignment is a type of
property_definition_relationship
that implements the ARM concept of
Derived_laminate_assignment.
EXPRESS specification:
*)
ENTITY derived_laminate_assignment
SUBTYPE OF (property_definition_relationship);
END_ENTITY;
(*
An interconnect_module_stratum_based_terminal is a type of
interconnect_module_terminal that implements the ARM concept
of Interconnect_module_stratum_based_terminal.
EXPRESS specification:
*)
ENTITY interconnect_module_stratum_based_terminal
SUBTYPE OF (interconnect_module_terminal);
END_ENTITY;
(*
A sequential_laminate_passage_based_fabrication_joint is a type of shape_aspect that
implements the ARM concept of Interconnect_module_product_assembly_view_fabrication_joint.
EXPRESS specification:
*)
ENTITY sequential_laminate_passage_based_fabrication_joint
SUBTYPE OF (shape_aspect);
END_ENTITY;
(*
A sequential_laminate_stackup_component is a type of
physical_component
that implements the ARM concept of
Sequential_laminate_stackup_component.
EXPRESS specification:
*)
ENTITY sequential_laminate_stackup_component
SUBTYPE OF (physical_component);
END_ENTITY;
(*
A sequential_laminate_stackup_definition is a type of
product_definition
that implements the ARM concept of
Sequential_laminate_stackup_definition.
EXPRESS specification:
*)
ENTITY sequential_laminate_stackup_definition
SUBTYPE OF (product_definition);
END_ENTITY;
(*
*)
END_SCHEMA; -- Sequential_laminate_assembly_design_mim
(*
© ISO 2018 — All rights reserved
